Hyundai Creta: Clutch System / Clutch Cover And Disc

Hyundai Creta GS 2014-2019 Service Manual / Clutch System / Clutch System / Clutch Cover And Disc

Components and components location

Components

1. Clutch release fork
2. Clutch cover assembly

3. Clutch disk assembly
4. Clutch release bearing

Repair procedures

Removal

1.	Remove the transaxle assembly. (Refer to Manual Transaxle System - "Manual Transaxle")

2.	Remove the clutch cover bolts. Be careful not to be bent or twist bolts. Loosen bolts in diagonal directions.

Inspection

1.	Inspect diaphragm spring wear which is in contact with a concentric slave cylinder bearing.

2.	Check the clutch cover and disc surface for wear or cracks.

3.	Check the clutch disc lining for slipping or oil marks.

Measure the depth from a clutch lining surface to a rivet. If the measured value is less than the specification below, replace it.

Clutch disc thckness (A) [when free]: 8.7 ± 0.3 mm (0.3425 ± 0.012 in.)

Clutch disc rivet depth (B): 0.3 mm (0.0118 in.)

Installation

•	If reinstalling used cover, the cover should be installed with its clutch disc as a set.

Replace a clutch cover and disc as a set.

•	When replacing only a disc, a slip problem can occur because of the load loss due to uneven surface wear.

•	When replacing only a disc, it can be difficult to cut power because the thickness of the disc won't permit it.

Apply grease on a disc spline part and transaxle input shaft spline part as required.

Possible problems when not following

•	When not applying: Excessive wear of splines and bad clutch operation can occur.

•	When excessively applying: Grease can be scattered bycentrifugal force which can conteminate the clutch disc. This can cause a loss of friction force causing a slip.

The 'T/M SIDE' marked surface should face transaxle.

Possible problems when the disc is installed in the opposite direction.

•	There can be an interference between the concentric slave cylinder on the TM side and a engine flywheel surface.

•	Transaxle shift error or a strange sound can occur due to clutch separation.

•	The concentric slave cylinder can break. If it does, the concentric slave cylinder should be replaced new one.

4.	Install the clutch disc and the cover with SST(No.: 09411-1P000).

Install the clutch cover bolts. Not to be bent or twisted, Tighten them in diagonal directions.

Tightening torque:

24.5 ~ 35.3 N.m (2.5 ~ 3.6 kgf.m, 18.1 ~ 26.0 lb-ft)

•	Loosely tighten every clutch cover bolts, then torque to specifications in a diagonal direction. This can prevent twisting, vibration of the cover, and the lifting of the pressure plate.

•	Install the all the components with the specified torques. If not, the clutch torque transaxle may have concerns or the mounting bolt can loosen.

6.	Install the manual transaxle assembly. (Refer to Manual Transaxle System - "Manual Transaxle")

Ignition Lock Switch

Specifications Specifications Item Specifications Working voltage DC 12V Operating force Initial posi ...

Other information:

Hyundai Creta GS 2014-2019 Service Manual: Components and components location
Components Location 1. ECM (Engine Control Module) 2. Manifold Absolute Pressure Sensor (MAPS) 3. Intake Air Temperature Sensor (IATS) 4. Engine Coolant Temperature Sensor (ECTS) 5. Throttle Position Sensor (TPS) [integrated into ETC Module] 6. Cranksha ...

Hyundai Creta GS 2014-2019 Service Manual: General information
Tightening Torque Table of Standard Parts BOLT (Nominal diameter) NUT (Nominal diameter) BOLT/NUT Normal screw Torque Nm (kg.m, Ib-ft) Nominal diameter. ...