Hyundai Creta: Parking Brake System / Parking Brake Cable: Repair procedures

Hyundai Creta GS 2014-2019 Service Manual / Brake System / Parking Brake System / Parking Brake Cable: Repair procedures

Removal

The parking brake cables must not be bent or distorted. This will lead to stiff operation and premature failure.

1.	Release the parking brake lever and parking brake cable is loose.

2.	Remove the floor console. (Refer to Body - "Floor Console")

3.	Loosen the adjusting nut (A) and remove the parking brake cables from the equalizer assembly.

4.	Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported.

Remove the rear wheel & tire (A).

Be careful not to damage the hub bolts when removing the rear wheel and tire.

6.	Loosen the screw and then remove the drum.

7.	Remove the upper shoe return spring (A), lower shoe return spring (B), level pawl (C) and djuster assembly (D).

8.	Remove the shoe hold assembly (A) and then remove the brake shoe.

9.	Disconnect the parking cable.

10.	Loosen the parking brake cable bracket bolts and remove the parking brake cable.

Installation

Install the parking brake cable.

Parking brake cable bracket mounting bolts:

8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

2.	Install the parking cable.

3.	Fix the brake shoe by installing the shoe hold assembly (A).

4.	Install the upper shoe return spring (A), lower shoe return spring (B), level pawl (C) and djuster assembly (D).

Install the drum by tighten the screw.

Tightening torque :

4.9 ~ 5.9 N.m (0.5 ~ 0.6 kgf.m, 3.6 ~ 4.3 lb-ft)

Install the rear wheel & tire (A).

Tightening torque :

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

Be careful not to damage the hub bolts when removing the rear wheel and tire.

7.	Loosen the adjusting nut (A) and remove the parking brake cables from the equalizer assembly.

8.	Install the floor console. (Refer to Body - "Floor Console")

Parking Brake Lever Stroke Adjustment

1.	Raise the vehicle, and make sure it is securely supported.

2.	Remove the floor console pad.

Adjust the parking brake lever stroke by turning adjusting nut (A).

Parking brake lever stroke :

5~7 cliks (Pull the lever with 20kgf)

•	After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

4.	Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.

5.	Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.

6.	Install the floor console.

Parking Brake Lever: Repair procedures

Removal • The parking brake cables must not be bent or distorted. This will le ...

ABS(Anti-Lock Brake System)

...

Other information:

Hyundai Creta GS 2014-2019 Service Manual: Specifications
Specifications Fuel Delivery System Items Specification Fuel Tank Capacity 55 lit. (14.5 U.S.gal., 58.1 U.S.qt, 48.4 Imp.gal.) Fuel Filter (built in Fuel Pump Assembly) Type ...

Hyundai Creta GS 2014-2019 Service Manual: Components and components location
Components 1. Roof trim 2. Sunvisor [LH] 3. Sunvisor [RH] 4. Assist handle ...