Hyundai Creta: General Tightening Torque Table / General information

Tightening Torque Table of Standard Parts
BOLT (Nominal diameter)
NUT (Nominal diameter)


BOLT/NUT Normal screw
Torque Nm (kg.m, Ib-ft)

Nominal diameter.
(mm)
Pitch [mm (in.) ]
4T
8T
10T

M5
0.8 (0.031)
2.0 ~ 3.0 (0.2 ~ 0.3, 1.4 ~ 2.2)
4.9 ~ 6.9 (0.5 ~ 0.7, 3.6 ~ 5.1)
7.8 ~ 10.8 (0.8 ~ 1.1, 5.8 ~ 8.0)
M6
1 (0.039)
2.9 ~ 4.9 (0.3 ~ 0.5, 2.2 ~ 3.6) 
8.8 ~ 12.7 (0.9 ~ 1.3, 6.5 ~ 9.4) 
13.7 ~ 18.6 (1.4 ~ 1.9, 10.1 ~ 13.7)
M8
1.25 (0.049)
8.8 ~ 11.8 (0.9 ~ 1.2, 6.5 ~ 8.7)
22.6 ~ 30.4 (2.3 ~ 3.1, 16.6 ~ 22.4) 
33.3 ~ 44.1 (3.4 ~ 4.5, 24.6 ~ 32.5)
M10
1.5 (0.059)
16.7 ~ 22.6 (1.7 ~ 2.3, 12.3 ~ 16.6)
45.1 ~ 60.8 (4.6 ~ 6.2, 33.3 ~ 44.8)
65.7 ~ 88.3 (6.7 ~ 9.0, 48.5 ~ 65.1)
M12
1.75 (0.068)
29.4 ~ 39.2 (3.0 ~ 4.0, 21.7 ~ 28.9)
78.5 ~ 105.9 (8.0 ~ 10.8, 57.9 ~ 78.1)
114.7 ~ 154.9 (11.7 ~ 15.8, 84.6 ~ 114.3)
M14
2 (0.078)
47.1 ~ 63.7 (4.8 ~ 6.5, 34.7 ~ 47.0)
125.5 ~ 169.7 (12.8 ~ 17.3, 92.6 ~ 125.1)
183.4 ~ 249.1 (18.7 ~ 25.4, 135.3 ~ 183.7)
M16
2 (0.078)
73.5 ~ 100.0 (7.5 ~ 10.2, 54.2 ~ 73.8)
197.1 ~ 266.7 (20.1 ~ 27.2, 145.4 ~ 196.7)
288.3 ~ 390.3 (29.4 ~ 39.8, 212.7 ~ 287.9)
M20
2.5 (0.098)
144.2 ~ 195.2 (14.7 ~ 19.9, 106.3 ~ 143.9)
396.2 ~ 535.4 (40.4 ~ 54.6, 292.2 ~ 394.9)
565.8 ~ 764.9 (57.7 ~ 78.0, 417.3 ~ 564.2)
M24
3 (0.118)
249.1 ~ 337.3 (25.4 ~ 34.4, 183.7 ~ 248.8)
687.4 ~ 929.7 (70.1 ~ 94.8, 507.0 ~ 685.7)
975.8 ~ 1320.0 (99.5 ~ 134.6, 719.7 ~ 973.6)
M30
3.5 (0.137)
499.2 ~ 674.7 (50.9 ~ 68.8, 368.2 ~ 497.6)
1372.9 ~ 1858.4 (140.0 ~ 189.5, 1012.6 ~ 1370.7)
1956.4 ~ 2647.8 (199.5 ~ 270.0, 1443.0 ~ 1952.9)

BOLT/NUT Thin screw
Torque Nm (kg.m, Ib-ft)
Nominal diameter.
(mm)
Pitch [mm (in.) ]
4T
8T
10T

M5
0.5 (0.019)
2.0 ~ 3.0 (0.2 ~ 0.3, 1.4 ~ 2.2)
5.9 ~ 8.8 (0.6 ~ 0.9, 4.3 ~ 6.5)
8.8 ~ 12.7 (0.9 ~ 1.3, 6.5 ~ 9.4)
M6
0.75 (0.029)
3.9 ~ 4.9 (0.4 ~ 0.5, 2.9 ~ 3.6)
9.8 ~ 13.7 (1.0 ~ 1.4, 7.2 ~ 10.1)
14.7 ~ 20.6 (1.5 ~ 2.1, 10.8 ~ 15.2)
M8
1 (0.039)
8.8 ~ 11.8 (0.9 ~ 1.2, 6.5 ~ 8.7)
24.5 ~ 32.4 (2.5 ~ 3.3, 18.1 ~ 23.9)
35.3 ~ 48.1 (3.6 ~ 4.9, 26.0 ~ 35.4)
M10
1.25 (0.049)
17.7 ~ 23.5 (1.8 ~ 2.4, 13.0 ~ 17.4)
47.1 ~ 63.7 (4.8 ~ 6.5, 34.7 ~ 47.0)
69.6 ~ 94.1 (7.1 ~ 9.6, 51.4 ~ 69.4)
M12
1.25 (0.049)
32.4 ~ 44.1 (3.3 ~ 4.5, 23.9 ~ 32.5)
86.3 ~ 117.7 (8.8 ~ 12.0, 63.7 ~ 86.8)
127.5 ~ 172.6 (13.0 ~ 17.6, 94.0 ~ 127.3)
M14
1.5 (0.059)
51.0 ~ 69.6 (5.2 ~ 7.1, 37.6 ~ 51.4)
136.3 ~ 185.3 (13.9 ~ 18.9, 100.5 ~ 136.7)
201.0 ~ 271.6 (20.5 ~ 27.7, 148.3 ~ 200.4)
M16
1.5 (0.059)
79.4 ~ 107.9 (8.1 ~ 11.0, 58.6 ~ 79.6)
211.8 ~ 286.4 (21.6 ~ 29.2, 156.2 ~ 211.2)
311.8 ~ 421.7 (31.8 ~ 43.0, 230.0 ~ 311.0)
M20
1.5 (0.059)
163.8 ~ 221.6 (16.7 ~ 22.6, 120.8 ~ 163.5)
448.2 ~ 607.0 (45.7 ~ 61.9, 330.5 ~ 447.7)
639.4 ~ 864.9 (65.2 ~ 88.2, 471.6 ~ 638.0)
M24
2 (0.078)
276.5 ~ 373.6 (28.2 ~ 38.1, 204.0 ~ 275.6)
759.0 ~ 1026.8 (77.4 ~ 104.7, 559.8 ~ 757.3)
1080.7 ~ 1462.2 (110.2 ~ 149.1, 797.1 ~ 1078.4)
M30
2 (0.078)
562.9 ~ 762.0 (57.4 ~ 77.7, 415.2 ~ 562.0)
1553.4 ~ 2102.5 (158.4 ~ 214.4, 1145.7 ~ 1550.8)
2210.4 ~ 2991.0 (225.4 ~ 305.0, 1630.3 ~ 2206.1)

Flange BOLT (Nominal diameter)
Flange NUT (Nominal diameter)


Flange BOLT/NUT Normal screw
Torque Nm (kg.m, Ib-ft)
Nominal diameter.
(mm)
Pitch [mm (in.) ]
4T
8T
10T

M5
0.8 (0.031)
2.0 ~ 2.9 (0.2 ~ 0.3, 1.4 ~ 2.2)
5.9 ~ 7.8 (0.6 ~ 0.8, 4.3 ~ 5.8)
8.8 ~ 11.8 (0.9 ~ 1.2, 6.5 ~ 8.7)
M6
1 (0.039)
3.9 ~ 4.9 (0.4 ~ 0.5, 2.9 ~ 3.6)
9.8 ~ 13.7 (1.0 ~ 1.4, 7.2 ~ 10.1)
14.7 ~ 19.6 (1.5 ~ 2.0, 10.8 ~ 14.5)
M8
1.25 (0.049)
8.8 ~ 11.8 (0.9 ~ 1.2, 6.5 ~ 8.7)
24.5 ~ 32.4 (2.5 ~ 3.3, 18.1 ~ 23.9)
35.3 ~ 48.1 (3.6 ~ 4.9, 26.0 ~ 35.4)
M10
1.5 (0.059)
17.7 ~ 24.5 (1.8 ~ 2.5, 13.0 ~ 18.1)
48.1 ~ 65.7 (4.9 ~ 6.7, 35.4 ~ 48.5)
70.6 ~ 96.1 (7.2 ~ 9.8, 52.1 ~ 70.9)
M12
1.75 (0.068)
31.4 ~ 43.1 (3.2 ~ 4.4, 23.1 ~ 31.8)
84.3 ~ 113.8 (8.6 ~ 11.6, 62.2 ~ 83.9)
123.6 ~ 167.7 (12.6 ~ 17.1, 91.1 ~ 123.7)
M14
2 (0.078)
51.0 ~ 68.6 (5.2 ~ 7.0, 37.6 ~ 50.6)
135.3 ~ 182.4 (13.8 ~ 18.6, 99.8 ~ 134.5)
198.1 ~ 268.7 (20.2 ~ 27.4, 146.1 ~ 198.2)
M16
2 (0.078)
79.4 ~ 107.9 (8.1 ~ 11.0, 58.6 ~ 79.6)
212.8 ~ 288.3 (21.7 ~ 29.4, 157.0 ~ 212.7)
311.8 ~ 421.7 (31.8 ~ 43.0, 230.0 ~ 311.0)

Flange BOLT/NUT Thin screw
Torque Nm (kg.m, Ib-ft)

Nominal diameter.
(mm)
Pitch [mm (in.) ]
4T
8T
10T

M5
0.5 (0.019)
2.9 ~ 2.9 (0.3 ~ 0.3, 2.2 ~ 2.2)
6.9 ~ 8.8 (0.7 ~ 0.9, 5.1 ~ 6.5)
9.8 ~ 13.7 (1.0 ~ 1.4, 7.2 ~ 10.1)
M6
0.75 (0.029)
3.9 ~ 5.9 (0.4 ~ 0.6, 2.9 ~ 4.3)
10.8 ~ 14.7 (1.1 ~ 1.5, 8.0 ~ 10.8)
16.7 ~ 21.6 (1.7 ~ 2.2, 12.3 ~ 15.9)
M8
1 (0.039)
9.8 ~ 12.7 (1.0 ~ 1.3, 7.2 ~ 9.4)
26.5 ~ 35.3 (2.7 ~ 3.6, 19.5 ~ 26.0)
38.2 ~ 52.0 (3.9 ~ 5.3, 28.2 ~ 38.3)
M10
1.25 (0.049)
19.6 ~ 25.5 (2.0 ~ 2.6, 14.5 ~ 18.8)
51.0 ~ 68.6 (5.2 ~ 7.0, 37.6 ~ 50.6)
75.5 ~ 102.0 (7.7 ~ 10.4, 55.7 ~ 75.2)
M12
1.25 (0.049)
35.3 ~ 48.1 (3.6 ~ 4.9, 26.0 ~ 35.4)
94.1 ~ 126.5 (9.6 ~ 12.9, 69.4 ~ 93.3)
138.3 ~ 186.3 (14.1 ~ 19.0, 102.0 ~ 137.4)
M14
1.5 (0.059)
55.9 ~ 75.5 (5.7 ~ 7.7, 41.2 ~ 55.7)
148.1 ~ 200.1 (15.1 ~ 20.4, 109.2 ~ 147.6)
216.7 ~ 293.2 (22.1 ~ 29.9, 159.8 ~ 216.3)
M16
1.5 (0.059)
86.3 ~ 116.7 (8.8 ~ 11.9, 63.7 ~ 86.1)
229.5 ~ 309.9 (23.4 ~ 31.6, 169.3 ~ 228.6)
336.4 ~ 455.0 (34.3 ~ 46.4, 248.1 ~ 335.6)

  
1)
The torques shown in the table are standard values under the following conditions.
•
Nuts and bolts are made of galvanized steel bar.
•
Galvanized plain steel washers are inserted.
•
All nuts, bolts and plain washers are dry.
2)
The torques shown in the table are not applicable.
•
When spring washers, toothed washers and the like are inserted.
•
If plastic parts are fastened.
•
If self-tapping screws or self-locking nuts are used.
•
If threads and surfaces are coated with oil.
General Tightening Torque Table
...

Important Safety Notice
...

Other information:

Hyundai Creta GS 2014-2019 Service Manual: Description and operation
Description Exhaust emissions (CO, HC, NOx) are controlled by a combination of engine modifications and the addition of special control components. Modifications to the combustion chamber, intake manifold, camshaft and ignition system form the basic control system. Thes ...

Hyundai Creta GS 2014-2019 Owners Manual: Blade replacement
When the wipers no longer clean adequately, the blades may be worn or cracked, and require replacement. NOTICE To prevent damage to the wiper arms or other components, do not attempt to move the wipers manually. NOTICE The use of a non-specified wiper blade could result in wiper malfun ...

© 2017-2026 www.hcrmangs.com