Hyundai Creta: Fuel Delivery System / Repair procedures

Fuel Pressure Test
1.
Release the residual pressure in fuel line.
(Refer to Fuel Delivery System - "Release Residual Pressure in Fuel Line")
  
When removing the fuel pump fuse, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the GDS after completion of "Release Residual Pressure in Fuel Line" work.
2.
Install the Special Service Tool (SST).
(1)
Disconnect the fuel feed tube from the delivery pipe.
  
There may be some residual pressure even after “Release Residual Pressure in Fuel Line” work, so cover the hose connection with a shop towel to prevent residual fuel from spilling out before disconnecting any fuel connection.
(2)
Install the special service tool for measuring the fuel pressure in between the fuel feed tube and the fuel delivery pipe (Refer to the figure below).

3.
Inspect fuel leakage on connections among the fuel feed tube, the delivery pipe, and the SST components with IG ON.
4.
Measure Fuel Pressure.
(1)
Start the engine and measure the fuel pressure at idle.
Fuel Pressure :
323 ~ 363 kPa (3.3 ~ 3.7 kgf/cm², 46.8 ~ 52.6 psi)
  
If the fuel pressure differs from the standard value, repair or replace the related part (Refer to the table below).
Fuel
Pressure
Cause
Related Part
Too Low
Fuel filter clogged
Fuel Filter
Fuel leakage
Fuel Pressure Regulator
Too High
Fuel pressure regulator valve stuck
Fuel Pressure Regulator

(2)
Stop the engine, and then check for the change in the fuel pressure gauge reading.
Standard Value : The gauge reading should hold for about 5 minutes after the engine stops
  
If the gauge reading should not be held, repair or replace the related part (Refer to the table below).
Fuel Pressure
(After Engine Stops)
Cause
Related
Part
Fuel Pressure Drops Slowly
Leakage on injector
Injector
Fuel Pressure Drops Immediately
Check valve of fuel pump stuck open
Fuel Pump

(3)
Turn the ignition switch OFF.
5.
Release the residual pressure in fuel line.
(Refer to Fuel Delivery System - "Release Residual Pressure in Fuel Line")
  
When removing the fuel pump fuse, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the GDS after completion of "Release Residual Pressure in Fuel Line" work.
6.
Test End
(1)
Remove the Special Service Tool (SST) from the fuel feed tube and the delivery pipe.
(2)
Connect the fuel feed tube and the delivery pipe.
Release Residual Pressure in Fuel Line
  
There may be some residual pressure even after "Release Residual Pressure in Fuel Line" work, so cover the hose connection with a shop towel to prevent residual fuel from spilling out before disconnecting any fuel connection.
1.
Turn the ignition switch OFF and disconnect the battery (-) terminal.
2.
Remove the fuel pump fuse (A).

3.
Connect the battery (-) terminal.
4.
Start the engine and let idle, and then turn the ignition switch OFF after the engine has stopped on its own.
5.
Disconnect the battery (-) cable, and then install the fuel pump relay (A).
6.
Connect the battery (-) terminal.
7.
Delete the Diagnostic Trouble Code (DTC) related the fuel pump relay with the GDS.
  
When removing the fuel pump fuse, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the GDS after completion of "Release Residual Pressure in Fuel Line" work.
Components and components location
Components Location 1. Fuel Tank 2. Fuel Pump 3. Fuel Filter 4. Fuel Pressure Regulator 5. Canister 6. Fuel Tank Air Filter 7. Fuel Tank Band 8. V ...

Fuel Tank: Repair procedures
Removal 1. Release the residual pressure in fuel line. (Refer to Delivery System - "Release Residual Pressure in Fuel Line") 2. ...

Other information:

Hyundai Creta GS 2014-2019 Service Manual: Drive Belt
Components and components location Components 1. Drive Belt Repair procedures Removal and Installation 1. Disconnect the battery negative terminal. 2. Loosen the alternator mounting bolts (A) ...

Hyundai Creta GS 2014-2019 Service Manual: Output Speed Sensor
Description and operation Description • Output speed sensor uses an electric current type hall sensor in which the current is changed by the magnetic variation. • Output speed sensor (A) and Input speed sensor are integrated a ...

© 2017-2019 www.hcrmangs.com